Connect With Us

DesignJet T7100 error codes

DesignJet T7100 error codes

DesignJet T7100 error codes

 

  • 01.0:10 – Main PCA hardware failure.
  • 01.1:10 -PrintMech PCA hardware failure.
  • 01.2:10 – ISS Top PCA communication failure.
  • 01.3:10 – ISS Bottom PCA communication failure.
  • 02.1:10 Carriage PCA communication failure
  • 03:10 – Cause: Power distribution failure
  • 05:10 – Formatter communication failure with ISS.
  • 05.1:10 – Formatter CPU fan stopped or burnt
  • 06:03 – Main NVM communication failure.
  • 06:10 – Main NVM communication failure
  • 08:11 – Front Panel communication failure.
  • 11:10 – Trailing Cable does not seem to be connected.
  • 17.0:11 – PrintMech to Interconnect Power cable does not seem to be connected.
  • 17.1:11 – PrintMech to Interconnect Data 1 cable does not seem to be connected
  • 17.2:11 – PrintMech to Interconnect Data 2 cable does not seem to be connected.
  • 17.3:11 – Main PCA to PrintMech Black 1 cable does not seem to be connected
  • .17.4:11 – Main PCA to PrintMech Blue 2 cable does not seem to be connected.
  • 21:03 – Service Station electrical current limit.
  • DesignJet T7100 error codes
  • 21:13 – Service Station jam.
  • 23:10 – Air Pressurization System failure; unable to pressurize or depressurize tubes.
  • 24:03 – Ink Supply Tubes purge failure.
  • 24:10 – A broken bag has been detected in one of the Ink Cartridges.
  • 24:11 – PrintMech to ISS Top cable does not seem to be connected.
  • 24.1:11 – ISS Top to ISS Bottom cable does not seem to be connected.
  • 26.0:01 – Bad contact detected in ISS slot 0 floater.
  • 26.1:01 – Bad contact detected in ISS slot 1 floater.
  • 26.2:01  – Bad contact detected in ISS slot 2 floater
  • 26.3:01 – Bad contact detected in ISS slot 3 floater.
  • 26.4:01 – Bad contact detected in ISS slot 4 floater.
  • 26.5:01 – Bad contact detected in ISS slot 5 floater.
  • 27.1:01 – Calibration failed to due to poor performance of the Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 1.
  • 27.2:01 – Calibration failed to due to poor performance of the Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 2.
  • 27.3:01 – Calibration failed to due to poor performance of the Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 3.
  • 27.4:01 – Calibration failed to due to poor performance of the Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 4.
  • 27.5:01 – Calibration failed to due to poor performance of the Matte Black Printhead (T7100) in slot 5; the T7100 Monochrome should not experience this error.
  • 27.6:01 – Calibration failed to due to poor performance of the Matte Black Printhead (T7100) in slot 6; the T7100 Monochrome should not experience this error.
  • 27.7:01 – Calibration failed to due to poor performance of the Gray/Dark Gray Printhead (T7100) in slot 7; the T7100 Monochrome should not experience this error.
  • 27.8:01 – Calibration failed to due to poor performance of the Gray/Dark Gray Printhead (T7100) in slot 8; the T7100 Monochrome should not experience this error.
  • 28.1:01 – The Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 1 is deteriorating.
  • 28.2:01 – The Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 2 is deteriorating.
  • 28.3:01 – The Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 3 is deteriorating.
  • 28.4:01 – The Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 4 is deteriorating.
  • 28.5:01 – The Matte Black Printhead (T7100) in slot 5 is deteriorating; the T7100 Monochrome should not experience this error.
  • 28.6:01 – The Matte Black Printhead (T7100) in slot 6 is deteriorating; the T7100 Monochrome should not experience this error.
  • 28.7:01 – The Gray/Dark Gray Printhead (T7100) in slot 7 is deteriorating; the T7100 Monochrome should not experience this error.
  • 28.8:01 – The Gray/Dark Gray Printhead (T7100) in slot 8 is deteriorating; the T7100 Monochrome should not experience this error.
  • 28.1:02 – The Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 1 is nearing the end of its useful life.
  • 28.2:02 – The Yellow Printhead (T7100) or Matte Black Printhead (T7100 Monochrome) in slot 2 is nearing the end of its useful life.
  • 28.3:02 – The Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 3 is nearing the end of its useful life.
  • 28.4:02 – The Magenta/Cyan Printhead (T7100) or Dark Gray Printhead (T7100 Monochrome) in slot 4 is nearing the end of its useful life.
  • 28.5:02 – The Matte Black Printhead (T7100) in slot 5 is nearing the end of its useful life; the T7100 Monochrome should not experience this error.
  • 28.6:02 – The Matte Black Printhead (T7100) in slot 6 is nearing the end of its useful life; the T7100 Monochrome should not experience this error.
  • 28.7:02 – The Gray/Dark Gray Printhead (T7100) in slot 7 is nearing the end of its useful life; the T7100 Monochrome should not experience this error.
  • 28.8:02 – The Gray/Dark Gray Printhead (T7100) in slot 8 is nearing the end of its useful life; the T7100 Monochrome should not experience this error.
  • 29:01 – Maintenance Cartridge not inserted correctly.
  • 29:02 – Ink Absorber almost full.
  • 35:10 – Rear Door sensor error detected.
  • DesignJet T7100 error codes
  • 37:03 – ARSS motor shutdown.
  • 38:03 – Stacker communication protocol error.
  • 38.0:01 – Paper jam detected in stacker; buffer sensor activated.
  • 38.0:10 – Paper jam detected in stacker; buffer sensor not activated.
  • 38.1:01 – Stacker communication error.
  • 38.1:03 – Stacker multiple firmware upgrades.
  • 38.1:04 – Stacker unable to upgrade firmware.
  • 38.1:10 – Stacker initialization error.
  • 38.2:03 – Stacker unable to reach target temperature.
  • 38.2:10 – Stacker temperature too high.
  • 38.2:11 – Stacker temperature too low.38.3:11 – Stacker heating element overhead switch off.
  • 38.4:10 – Stacker heating element failure.
  • 38.5:01 – Stacker motor overload.
  • 38.5:10 – Stacker abnormal motor condition
  • 38.5:11 – Stacker motor encoder failure.
  • 38.6:11 – Stacker power supply failure.
  • DesignJet T7100 error codes
  • 38.8:01 – Paper jam detected in stacker; paper jam sensor activated.
  • 38.8:10 – Paper jam detected in stacker; paper jam sensor not activated.
  • 39.1:01.2 – Unable to load roll 1 from standby/parking position; roll mispositioned
  • 39.2:01.2 – Unable to load roll 2 from standby/parking position; roll mispositioned.
  • 39.2:01.2 – Unable to load roll 3 from standby/parking position; roll mispositioned.
  • 39.1:01.3 – Unable to load roll 1 from standby/parking position; paper edges were not found.
  • 39.2:01.3  – Unable to load roll 2 from standby/parking position; paper edges were not found.
  • 39.2:01.3  – Unable to load roll 3 from standby/parking position; paper edges were not found.
  • 40:03  – Smart Roll-loading System Motor shutdown.
  • 41:03  – Paper motor electrical current limit.
  • 42:03  – Scan-Axis motor electrical current limit.
  • 43:01 – Vacuum Fan spinning at wrong speed.
  • 43:10 – Vacuum Fan failure.
  • 43.1:10 – Vacuum Driver PCA communication or hardware failure.
  • 43:11 – Vacuum Fan PCA cable does not seem to be connected.
  • 44.2:10 – Right Aerosol Fan stopped or spinning at lower speed.
  • 44.4:10 – Right Aerosol Fan Filter blocked.
  • 45:03 – Rewinder servo shutdown.
  • 46:03 – Primer servo shutdown.
  • 46:13 – Primer test distance failed.
  • 50:03 – OMAS fatal error or disconnected.
  • 50.1:10 – OMAS Module communication failure.
  • DesignJet T7100 error codes
  • 50:14 – Firmware version mismatch between the OMAS Controller Card and Hard Disk Drive.
  • 50.2:10 – OMAS Controller Card communication failure.
  • 50.3:11 – Main PCA to OMAS Controller cable does not seem to be connected.
  • 51:10 – Error detected in the Window Position Sensor.
  • 51.1:10 – Error detected in the Maintenance Cartridge Door Sensor (Service Station Door Sensor).
  • 51.9:10 – Smart Roll-loading System Door Sensor error detected.
  • 52:10 – Drop Detector switch On/Off failure.
  • 53:10 – Media Sensor error.
  • 53.1:11 – Media Sensor cable does not seem to be connected.
  • 55:10 – Line Sensor communication failure.
  • 56:01 – Incorrect readings from paper encoder.
  • 56:10 – Paper Encoder calibration failed.
  • 59.1:09 – Two electrical parts have been replaced at the same time.
  • 59.2:00 – An unsupported or reused part has been installed.
  • 60.1:11 – Initialization error
  • 60.2:17 – Initialization error.
  • 61:01 – The file format is incorrect and the printer cannot process the job.
  • 61:04.1 – The PostScript fonts are missing.
  • 61:04.2 – PostScript unknown Paper ID.
  • 61:08 – The paper type specified in the file is incorrect and the printer cannot process the job.
  • 61:08.1 – The file cannot be printed because it is password-protected.
  • 61:08.2 – The file contains format errors or incorrect settings and the printer cannot process the job.
  • 61:10 – A slow computer processing complex files can pause for longer than the default printer timeout, which can be interpreted by the printer as an End Of Job, in which case some elements of the job may be lost.
  • 64.1:01 – The printer does not recognize the USB Hard Disk Drive accessory.
  • 71:03 – Out of memory failure.
  • 71:08 – Insufficient display list.
  • 74:01 – Error uploading firmware update file
  • DesignJet T7100 error codes
  • 75.21:10 – Total printer ink consumption reached upper limit.
  • 76:03 – Hard Disk Drive out of space.
  • 77:04 – Embedded Web Server internal software error.
  • 78.1:04 – Media Settings area missing in media settings file.
  • 79:03 – Generic firmware error.
  • 79:04 – Generic firmware error.
  • 79.2:04 – Operating-system signal error.
  • 81:01 – Paper servo shutdown; possible paper jam.
  • 85:03 – Problem finding the Drive Roller zero.
  • 86:01 – Carriage servo shutdown; possible paper jam.
  • 86:11 – Scan-Axis length requires too much force or energy.
  • 87:01 – Problem with the Scan Axis encoder sensor readings. 
  • 87:10 – Problem with the Carriage Encoder Sensor readings.
  • 88:10 – Smart Roll-loading System Position Sensor error detected.
  • DesignJet T7100 error codes

DesignJet T7100 error codes

alternatieve HP inkten   kompatible Tintenpatronen für HP   Frankrijk Fennemania   Italy Fennemania  

 

Compatible HP761 ink cartridge for the T7100/T7200

 

  • HP 761 DesignJet Maintenance Cartridge

    HP761 DesignJet Maintenance Cartridge (CH659A)

    65.72

  • HP 761 400-ml Grey DesignJet Ink Cartridge(CM995A)

    Replacement Cartridge for HP 761 Grey 400 ml CM995A

    60.00

    Rated 5.00 out of 5
  • HP 761 400-ml Yellow DesignJet Ink Cartridge(CM992A)

    Replacement Cartridge for HP 761 Yellow 400 ml. CM992A

    60.00

    Rated 5.00 out of 5
  • HP 761 775-ml Matte Black DesignJet Ink Cartridge(CM997A)

    Replacement Cartridge for HP 761 Matte Black 775 ml. CM997A

    95.00

    Rated 5.00 out of 5
  • HP 761 400-ml Cyan DesignJet Ink Cartridge(CM994A)

    Replacement Cartridge for HP 761 Cyan 400 ml. CM994A

    60.00

    Rated 5.00 out of 5
  • HP 761 400-ml Dark Grey DesignJet Ink Cartridge(CM996A)

    Replacement Cartridge for HP 761 Dark Grey 400 ml CM996A

    60.00

    Rated 5.00 out of 5
  • HP 761 400-ml Magenta DesignJet Ink Cartridge(CM993A)

    Replacement Cartridge for HP 761 Magenta 400 ml. CM993A

    60.00

    Rated 5.00 out of 5
  • HP 761 Magenta/Cyan Designjet Printhead (CH646A)

    HP 761 Magenta/Cyan Designjet Printhead (CH646A)

    125.00

  • Genuine Grey HP 761 Ink Cartridge - (CM995A)

    Genuine Grey HP 761 Ink Cartridge – (CM995A)

    149.24

  • Genuine Magenta HP 761 Ink Cartridge - (CM993A)

    Genuine Magenta HP 761 Ink Cartridge – (CM993A)

    149.24

  • Genuine Dark Grey HP 761 Ink Cartridge - (CM996A)

    Genuine Dark Grey HP 761 Ink Cartridge – (CM996A)

    149.24

  • Genuine Cyan HP 761 Ink Cartridge - (CM994A)

    Genuine Cyan HP 761 Ink Cartridge – (CM994A)

    149.24

Compatible HP designjet cartridge

Our compatible HP Designjet ink cartridges for HP printers are formulated to deliver the highest performance with even greater image quality, highly accurate color reproduction & superior print longevity, our ink is manufactured to the highest standards specifically for Hewlett Packard’s printers.

Top quality archival rated pigment compatible HP Designjet ink cartridges designed for HP wide format printers, saving money on volume printing with reliable chips and plug and play cartridges. We have a range of test printers and we manufacture all the cartridges so we really do have the invaluable hands on experience to advise you. We now have 1000’s of users making huge savings on their ink costs using our systems and inks whilst retaining the longevity (fade resistance) and image quality of the original. DesignJet T7100 error codes

Our compatible HP Designjet ink cartridges also provides exceptional durability & media compatibility. Just Plug & Print compatibility allowing the user to switch inks without the need to flush the lines or change the color profile just like the original.

DesignJet T7100 error codes